04 - Laserfiche WebLink

0689090 Divider, Hose Bed, .25" Unpainted, w/Handhold HOSE BED DIVIDER Five (5) hosebed dividers will be furnished for separating hose. Each divider will be constructed of a .25" brushed aluminum sheet. Flat surfaces will be sanded for uniform appearance, or constructed of brushed aluminum. An oval opening will be provided near the rear of the divider to be used as a hand hold and aid in accessing the hose bed. Divider will be fully adjustable by sliding in tracks, located at the front and rear of the hose bed. Divider will be held in place by tightening bolts, at each end. Acorn nuts will be installed on all bolts in the hose bed which have exposed threads. 0010133 Cross-Divider, Hose Bed A cross-divider will be provided just behind the fill tower. The divider will be bolted to the side sheet. 0729492 Cover, Hose Bed, Alum Treadplate, Bolted T-Bar, Electric Actuated HOSE BED COVER ELECTRIC ACTUATOR A two (2) section hose bed cover, constructed of .125" bright aluminum treadplate will be furnished. The cover will be hinged with full length stainless steel piano hinge. The sides will be slanted down with the center of the cover supported by a modular stationary bridgework support. The covers will not over lap. The cover will be reinforced so that it can support the weight of a man walking on the cover. A pneumatic gas spring assist will be installed at the front of the covers to help support and stabilize the cover throughout its range of motion. If access to water tank fill tower is blocked by the hose bed cover, then a hinged door will be provided in it so that tank may be filled without raising cover doors. Chrome grab handles and two (2) (one (1) each side) electric linear actuator with brake cylinders will be provided to assist in opening and closing the cover. A rubber-covered momentary toggle switch will be provided for each actuator that controls the opening and closing of the covers. Each switch will be located at the rear body of the body at the left side. Additional locks on top of the cover are not required to secure the cover in the nested position. A cross divider will be provided directly behind the actuators, at the front of the hose bed, to support the actuators and provide a clean appearance. A handrail will be provided at the rear, in the center of the support, to assist in climbing up the back of the truck. The hose bed cover will be connected to the Do Not Move Truck indicator. The light will be activated if the cover is not in the stowed position and the parking brake is released. 0647461 SP Flap, Rear of Alum Hose Bed Cover, Vinyl, Seat Belt Buckle, Split A pair of black vinyl flaps will be installed on the rear of the bright aluminum treadplate hose bed cover, with a chain weight and two (2) black straps with seat belt buckles will be provided at the rear of the cover with excess sewn in a loop. The top portion of each seat belt buckle strap and latch will be stitched onto the vinyl flap with the latch loose. The bottom strap and male portion of the latch will be attached to the base of the hose bed via a footman's loop and adjustable in length. The two flaps will overlap at the center with velcro. 0695399 Running Boards, 14.75" Deep, Front and Rear 45 Degree Corners RUNNING BOARDS Running boards will be fabricated of .125" bright aluminum treadplate. Each running board will be supported by a welded 2.00" square tubing and channel assembly, which will be bolted to the pump compartment substructure. Running boards will be 14.75" deep and spaced .50" away from the pump panel. The front and rear outside corner of the running board will be finished with a 45 degree corner where it lines up with the body. A splash guard will be provided above the running board treadplate. 0689497 Tailboard, T-Shaped, 24" & 8" Deep, Angled Corners TAILBOARD The tailboard will also be constructed of .125" bright aluminum treadplate and spaced .50" from the body, as well as supported by a structural steel assembly. The tailboard area will be 24.00" deep in the center area and 8.00" deep to the rear of the side compartments. The tailboard will be T-shaped. The outboard sides of the tailboard will be angled at 45 degrees beginning at the point where the body meets the tailboard at the outboard edge angling rearward to the rear edge of the tailboard. The exterior side will be flanged down and in for increased rigidity of tailboard structure. 0690037 Wall, Rear, Smooth Aluminum/Body Material REAR WALL, SMOOTH ALUMINUM/BODY MATERIAL The rear facing surfaces of the center rear wall will be smooth aluminum. The bulkheads, the surface to the rear of the side body compartments, will be smooth and the same material as the body. Any inboard facing surfaces below the height of the hosebed will be aluminum diamondplate. 36717Bid #: