04 - Laserfiche WebLink

0028244 Tank, Water, 500 Gallon, Poly, Med WATER TANK Booster tank will have a capacity of 500 gallons and be constructed of polypropylene plastic by United Plastic Fabricating, Incorporated. Tank joints and seams will be nitrogen welded inside and out. Tank will be baffled in accordance with NFPA Bulletin 1901 requirements. Baffles will have vent openings at both the top and bottom to permit movement of air and water between compartments. Longitudinal partitions will be constructed of .38" polypropylene plastic and will extend from the bottom of the tank through the top cover to allow for positive welding. Transverse partitions will extend from 4.00" off the bottom of the tank to the underside of the top cover. All partitions will interlock and will be welded to the tank bottom and sides. Tank top will be constructed of .50" polypropylene. It will be recessed .38" and will be welded to the tank sides and the longitudinal partitions. Tank top will be sufficiently supported to keep it rigid during fast filling conditions. Construction will include 2.00" polypropylene dowels spaced no more than 30.00" apart and welded to the transverse partitions. Two (2) of the dowels will be drilled and tapped (.50" diameter, 13.00" deep) to accommodate lifting eyes. A sump that will be sized dependent on the tank to pump plumbing will be provided at the bottom of the water tank. Sump will include a drain plug and the tank outlet. Tank will be installed in a fabricated cradle assembly constructed of structural steel. Sufficient crossmembers will be provided to properly support bottom of tank. Crossmembers will be constructed of steel bar channel or rectangular tubing. Tank will "float" in cradle to avoid torsional stress caused by chassis frame flexing. Rubber cushions, .50" thick x 3.00" wide, will be placed on all horizontal surfaces that the tank rests on. Stops or other provision will be provided to prevent an empty tank from bouncing excessively while moving vehicle. Mounting system will be approved by the tank manufacturer. 0003405 Overflow, 4.00" Water Tank, Poly Fill tower will be constructed of .50" polypropylene and will be a minimum of 8.00" wide x 14.00" long. Fill tower will be furnished with a .25" thick polypropylene screen and a hinged cover. An overflow pipe, constructed of 4.00" schedule 40 polypropylene, will be installed approximately halfway down the fill tower and extend through the water tank and exit to the rear of the rear axle. 0028104 Foam Cell Required 0024431 Modified Poly Tank for Hard Suction Hose, One Side 0553729 Not Required, Restraint, Water Tank, Heavy Duty 0003429 Not Required, Direct Tank Fill 0003424 Not Required, Dump Valve 0048710 Not Required, Jet Assist 0030007 Not Required, Dump Valve Chute 0514778 Not Required, Switch, Tank Dump Master 0126633 Hose Bed, Aluminum, Pumper HOSE BED The hose bed will be fabricated of .125"-5052 aluminum with a nominal 38,000 psi tensile strength. Upper and rear edges of side panels will have a double break for rigidity. The upper inside area of the beavertails will be covered with brushed stainless steel to prevent damage to painted surface when hose is removed. Flooring of the hose bed will be removable aluminum grating with the top surface corrugated to aid in hose aeration. The grating slats will be a minimum of 0.50" x 4.50" with spacing between slats for hose ventilation. 0723549 Painted Hose Bed The hose bed interior walls will be painted to match the lower body color. 0003481 Hose Bed Capacity, Special Hose bed will accommodate Driver side to passenger side as follows- 200' of 1.75" DJ Hose / 200' of 1.75" DJ Hose / 600' of 5.00" LDH / 600' of 2.50" DJ Hose / 200' of 2.50" DJ Hose / 600' of 1.50" SJ Forestry Hose . 35717Bid #: