04 - Laserfiche WebLink

0600350 Shelves, Adj, 500 lb Capacity, Full Width/Depth, Predefined Locations ADJUSTABLE SHELVES There will be 11 shelves with a capacity of 500 lb provided. The shelf construction will consist of .188" aluminum painted spatter gray with 2.00" sides. Each shelf will be infinitely adjustable by means of a threaded fastener, which slides in a track. The shelves will be held in place by .12" thick stamped plated brackets and bolts. The location(s) will be in RS1 in the lower third, in RS3 in the lower third, in RS3 in the upper third, in RS3 in the lower third, in RS1 in the upper third, in RS1 in the upper third, in LS2 centered between the floor and ceiling, in LS3 centered between the floor and ceiling, in LS1 in the upper third to the left of the partition, in LS1 in the upper third to the left of the partition and in B1 in the upper third. 0647045 Tray, Floor Mounted, Slide-Out, Full Width/Full Depth, 500lb, 2.00" Sides, 2G SLIDE-OUT FLOOR MOUNTED TRAY There will be two (2) floor mounted slide-out tray(s) with 2.00" sides provided LS1 left of the partition and B1. Each tray will be rated for up to 500lb in the extended position. The tray(s) will be constructed of a minimum .13" aluminum. The finish will be painted spatter gray. The trays will be designed for maximum compartment width and depth. There will be two undermount-roller bearing type slides rated at 250lb each provided. The pair of slides will have a safety factor rating of 2. To ensure years of dependable service, the slides will be coated with a finish that is tested to withstand a minimum of 1,000 hours of salt spray per ASTM B117. To ensure years of easy operation, the slides will require no more than a 50lb force for push-in or pull-out movement when fully loaded after having been subjected to a 40 hour vibration (shaker) test under full load. The vibration drive file will have been generated from accelerometer data collected from a heavy truck chassis driven over rough gravel roads in an unloaded condition. Proof of compliance will be provided upon request. Automatic locks will be provided for both the "in" and "out" positions. The trip mechanism for the locks will be located at the front of the tray for ease of use with a gloved hand. 0725642 Cabinet, Drawer Assembly, CTECH, Three Drawers, Up To 36" Wide DRAWER ASSEMBLY A slide-out drawer assembly will be installed LS3. The clear dimensions of the first drawer starting at the top will be 3.00" with a face plate that is 4.00" high x 21.00" deep. The clear dimensions of the second drawer will be 7.75" with a face plate that is 8.00" high x 21.00" deep. The clear dimensions of the third drawer will be 7.75" with a face plate that is 8.00" high x 21.00" deep. Each drawer will be the same width and not exceed 36.00". The drawers will have a capacity of 250 pounds. The drawers will be mounted in a cabinet housing constructed of light gray powder coated aluminum with anodized aluminum frames. The housing will be 24.00" deep, and completely enclose the drawer. A full-length aluminum extruded rail will be provided at the top edge of each drawer. This rail will act as the latching mechanism as well as the handle for each drawer. There will be a total of one (1) provided. 0540317 Toolboard, Swing-out, Alum, .188", Peg Board SWING OUT TOOLBOARD A swing out aluminum toolboard will be provided. It will be a minimum of .188" thick with .203" diameter holes in a pegboard pattern with 1.00" centers between holes. A 1.00" x 1.00" aluminum tube frame will be welded to the edge of the pegboard. The board will be mounted on a pivoting device at the back of the compartment on the top and bottom to allow easy movement in and out of the compartment. The maximum tool load will be 400 pounds. The board will have positive lock in the stowed and extended position. The board will have a D-ring handle to secure it in the stowed position. The board will be mounted on adjustable tracks from front to back within the compartment. There will be One (1) toolboard(s) provided. The toolboard(s) will be spatter gray painted and installed RS2 full height and width. 0726441 Partition, Trans Rear Compt PARTITION, TRANSVERSE REAR COMPARTMENT Two (2) partitions will be bolted in place to separate the left and right side rear compartments from the rear tailboard compartment. The partition will be body material painted spatter gray. 0726457 Partition, Vertical Compt, Predefined Locations VERTICAL COMPARTMENT PARTITION One (1) partition will be provided. The partition construction will consist of body material painted spatter gray. Each partition will be the full vertical height of the compartment. The location(s) will be in LS1, 28.00" from the forward door frame. 0517914 SP Gap, Sealed Water Tight, Floor, Side, Wall SEALED GAPS Any gaps in compartment floor, side, walls will be sealed tight. 0028022 Matting, Dri-Deck Shelving Only MATTING, COMPARTMENT SHELVING Dri-Deck rubber compartment matting will be provided in 13 shelves. The locations are, all shelves and trays. The Dri-Deck will be black and .562" thick with holes in the decking to allow air to flow. 41717Bid #: