04 - Laserfiche WebLink

0092582 Load Manager/Sequencer, MUX ELECTRONIC LOAD MANAGER An electronic load management (ELM) system will be provided that monitors the vehicles 12-volt electrical system, automatically reducing the electrical load in the event of a low voltage condition, and automatically restoring the shed electrical loads when a low voltage condition expires. This ensures the integrity of the electrical system. For improved reliability and ease of use, the load manager system will be an integral part of the vehicle's solid state control system requiring no additional components to perform load management tasks. Load management systems which require additional components will not be allowed. The system will include the following features: System voltage monitoring. A shed load will remain inactive for a minimum of five minutes to prevent the load from cycling on and off. Sixteen available electronic load shedding levels. Priority levels can be set for individual outputs. High Idle to activate before any electric loads are shed and deactivate with the service brake. If enabled: "Load Man Hi-Idle On" will display on the information center. Hi-Idle will not activate until 30 seconds after engine start up. Individual switch "on" indicator to flash when the particular load has been shed. The information center indicates system voltage. The information center, where applicable, includes a "Load Manager" screen indicating the following: Load managed items list, with priority levels and item condition. Individual load managed item condition: ON = not shed SHED = shed SEQUENCER A sequencer will be provided that automatically activates and deactivates vehicle loads in a preset sequence thereby protecting the alternator from power surges. This sequencer operation will allow a gradual increase or decrease in alternator output, rather than loading or dumping the entire 12 volt load to prolong the life of the alternator. For improved reliability and ease of use, the load sequencing system will be an integral part of the vehicle's solid state control system requiring no additional components to perform load sequencing tasks. Load sequencing systems which require additional components will not be allowed. Emergency light sequencing will operate in conjunction with the emergency master light switch. When the emergency master switch is activated, the emergency lights will be activated one by one at half-second intervals. Sequenced emergency light switch indicators will flash while waiting for activation. When the emergency master switch is deactivated, the sequencer will deactivate the warning light loads in the reverse order. Sequencing of the following items will also occur, in conjunction with the ignition switch, at half- second intervals: Cab Heater and Air Conditioning Crew Cab Heater (if applicable) Crew Cab Air Conditioning (if applicable) Exhaust Fans (if applicable) Third Evaporator (if applicable) 0783153 Headlights, Rect LED, JW Spkr Evo 2, AXT/DCF/Enf/Imp/Sab/Vel HEADLIGHTS There will be four (4) JW Speaker®, Model 8800, 4" x 6" rectangular LED lights mounted in the front quad style, chrome housing on each side of the cab grille: the outside light on each side will contain a part number 055***1 low beam module the inside light on each side will contain a part number 055***1 high beam module the headlights to include chrome bezels The low beam lights will be activated when the headlight switch is on. The high beam and low beam lights will be activated when the headlight switch and the high beam switch is activated. 0797346 Light, Directional, Wln 600 Cmb, Cab Crn, Wrp Bzl Otside Wrn Lts Enf, Sab FR DIRECTIONAL LIGHTS There will be two (2) Whelen 600 series, amber LED combination directional/marker lights provided. The lights will be located on the outside cab corners, next to the warning lights. The lens color(s) to be clear. 0750542 Light, Directional/Marker, Intermediate, Truck-Lite 60421Y LED 2lts INTERMEDIATE LIGHT There will be two (2) Truck-Lite®, Model 60421Y, amber LED lights furnished, one (1) each side, horizontally in the rear fender panel. The light will double as a turn signal and marker light. A stainless steel trim will be included with this installation. 0735474 Lights, Clearance/Marker/ID, Front, P25 LED 7 Lts, Saber FR/Enforcer CAB CLEARANCE/MARKER/ID LIGHTS There will be seven (7) amber LED lights provided per the following: Three (3) amber LED identification lights will be installed in the center of the cab above the windshield. Two (2) amber LED clearance lights will be installed, one (1) on each outboard side of the cab above the windshield as close to the outside of the apparatus as practical. Two (2) amber LED clearance lights will be installed, one (1) on each side of the cab as high and far forward as practical. The lights will be installed without guards. 31717Bid #: