Laserfiche WebLink
0681408 Hangers For Headsets, NFPA, Each <br /> <br />HEADSET HANGERS <br />There will be four (4) headset hanger(s) installed driver's seat, officer's seat, driver's side inboard <br />forward facing seat and passenger's side inboard forward facing seat. The hanger(s) will meet <br />NFPA 1901, Section 14.1.11, requirement for equipment mounting. <br />0517372 Switch, AM/FM Radio, Location and <br />Power Feature <br />REMOTE ON/OFF SWITCH FOR AM/FM RADIO <br />A remote, radio on/off switch will be located switch panel #4 (default to "on" with battery switch) . <br />The switch power will be directly to the battery switched power . <br />0559503 Install Customer Provided, Portable <br />Radio Charger(s) <br />PORTABLE RADIO CHARGER INSTALLATION <br />There will be eight (8) customer supplied portable two-way radio chargers(s) sent to the <br />apparatus manufacturers preferred radio installer to be installed 4 BK and 4 Motorola, TBD. <br />Specific shipping requirements will be followed. <br />0687904 Antenna Mount, Custom Chassis, <br />Cable Routed to Behind Officer Seat <br /> <br />RADIO ANTENNA MOUNT <br />There will be four (4) standard 1.125", 18 thread antenna-mounting base(s) installed TBD on the <br />cab roof with high efficiency, low loss, coaxial cable(s) routed to behind the officer seat. A <br />weatherproof cap will be installed on the mount. <br />0653526 Camera, Pierce, LS Mux, R, Camera VEHICLE CAMERA SYSTEM <br />There will be a color vehicle camera system provided with the following: <br />One (1) camera located at the rear of the apparatus, pointing rearward, displayed automatically <br />with the vehicle in reverse <br />The camera images will be displayed on the left side vehicle information center display. Audio <br />from the microphone on the active camera will be not provided. <br />The following components will be included: <br />One (1) SV-CW134639CAI, camera <br />One (1) amplified speaker (if applicable) <br />All necessary cables <br />0814831 Not Required, Camera Switcher CAMERA SWITCHER <br />A camera switcher is not required. <br />0523921 Recess, Rear Vision Camera <br /> <br />RECESS REAR CAMERA <br />A rear camera recess will be provided in the center at the rear . <br />0890416 Pierce Command Zone, Advanced <br />Electronics & Control System, <br />Enforcer, WiFi CZT <br />ELECTRICAL POWER CONTROL SYSTEM <br />The primary power distribution will be located forward of the officer's seating position and be <br />easily accessible while standing on the ground for simplified maintenance and troubleshooting. <br />Additional electrical distribution centers will be provided throughout the vehicle to house the <br />vehicle's electrical power, circuit protection, and control components. The electrical distribution <br />centers will be located strategically throughout the vehicle to minimize wire length. For ease of <br />maintenance, all electrical distribution centers will be easily accessible. All distribution centers <br />containing fuses, circuit breakers and/or relays will be easily accessible. <br />Distribution centers located throughout the vehicle will contain battery powered studs for <br />supplying customer installed equipment thus providing a lower cost of ownership. <br />Circuit protection devices, which conform to SAE standards, will be utilized to protect electrical <br />circuits. All circuit protection devices will be rated per NFPA requirements to prevent wire and <br />component damage when subjected to extreme current overload. General protection circuit <br />breakers will be Type-I automatic reset (continuously resetting). When required, automotive type <br />fuses will be utilized to protect electronic equipment. Control relays and solenoid will have a direct <br />current rating of 125 percent of the maximum current for which the circuit is protected per NFPA. <br />Solid-State Control System <br />A solid-state electronics based control system will be utilized to achieve advanced operation and <br />control of the vehicle components. A fully computerized vehicle network will consist of electronic <br />modules, electronic control modules to include black housings, a power indicator and status <br />indicator located near their point of use to reduce harness lengths and improve reliability. The <br />control system will comply with SAE J1939-11 recommended practices. <br />The control system will operate as a master-slave system whereas the main control module <br />instructs all other system components. The system will contain patented Mission Critical software <br />that maintains critical vehicle operations in the unlikely event of a main controller error. The <br />system will utilize a Real Time Operating System (RTOS) fully compliant with OSEK/VDX™  <br />specifications providing a lower cost of ownership. <br />For increased reliability and simplified use the control system modules will include the following <br />attributes: <br />Green LED indicator light for module power <br />Red LED indicator light for network communication stability status <br />Control system self test at activation and continually throughout vehicle operation <br />No moving parts due to transistor logic <br />Software logic control for NFPA mandated safety interlocks and indicators <br />Integrated electrical system load management without additional components <br />Integrated electrical load sequencing system without additional components <br />Customized control software to the vehicle's configuration <br />Factory and field programmable to accommodate changes to the vehicle's operating parameters <br />To assure long life and operation in a broad range of environmental conditions, the solid-state <br />control system modules will meet the following specifications: <br />Module circuit board will meet SAE J771 specifications <br />27717Bid #: